Internet Speed Test News How to connect two routers wirelessly?

How to connect two routers wirelessly?

Do you need a reliable network that will cover the entire area of the house, including the workshop, garage or porch and yard? With two interconnected routers, you can easily do this, the wireless solution is also much simpler and you can change the location of the routers without re-installing the interconnecting cables. Installation a wireless network with two bridges connected by routers is not extremely complicated. With this detailed guide, you can definitely do it!

Not every router will be suitable

Bridging can only be done by some types of routers, you have to check that first. If they don't support the "Bridge" or "Repeater" mode feature (which happens especially with low-cost models), you can try uploading a custom open source firmware (DD-WRT) that makes the feature available, but it probably won't work for every single. If you are purchasing new routers to build a wireless network, check compatibility with the DD WRT feature on the Internet before purchasing devices. For devices that you already have at home, you will find out the availability of the "Bridge" mode from the documentation that you received with the device when you purchased it. However, if the router cannot be used to make a wireless network, don't worry, you can connect the network with a network cable.

Step by step instructions

  • For an easier setup, bring both routers to your computer, place them in the selected places only after completing the setup process and verifying the functionality of the network.
  • You select one of the routers as the MAIN (primary) and the other will serve as the secondary. For the primary router, make the settings as if it were intended for normal Wi-Fi signal transmission. Connect it to the modem and computer with a network cable. You will not disconnect it until the wireless setup process is complete. You definitely need to make a note of his IP address, DHCP range and subnet mask. If the routers are of a different type and one has more powerful antennas, you will always choose it as the primary one. This will allow the secondary router to be placed as far away as possible, thus maximizing signal coverage. The next step will be to set up the secondary router. To do this, connect the secondary router to the computer via a network cable, and then open its configuration page. There is no need to connect the secondary router to the modem, after logging in you will search for pages marked "Wireless" or "Internet". Then turn on "Bridge" mode by selecting "Wireless Mode", "Network Mode" or "Connection Type" settings you will choose "Bridge mode" or "Repeater Mode". If you have used the DD-WRT firmware, you must select the "Repeater Bridge" mode. If none of the above menus appear on your connected computer, this router probably doesn't support bridging mode, so use a network cable connection. You will now specify the IP address of the secondary router by entering it according to the range of the main (primary) router. Example: If the IP address of the primary router is, for example, 192.168.1.1, enter 192.168.1.50 or similar, but always within the DHCP range of the main (primary) router. Be sure to check that the network mask matches the mask setting on the main router.
  • At the end of the settings, you enter the unique SSID (Service Set Identifier). This will allow you to distinguish which router on the network you are connecting to. It is usually best to connect to a closer router, but if you move frequently with a mobile receiver, be sure to choose a stronger signal. The primary and secondary routers can be named arbitrarily, but the combination of letters or numbers resembling the license plate on the car is not the right one for orientation, rather choose a more descriptive designation (such as "room", floor ", home 1", etc.).
  • Check the security method settings, which must be the same on both routers (WEP, WPA, WPA2) and the password you entered. This completes the setup and the routers should work properly. The last step you take after verifying the functionality of the network is to place the secondary router where you want the signal to repeat (that is, where you need to extend it). Make sure that there are no obstacles for the signal between the primary and secondary router (reinforced concrete structures, metal mesh in the walls and partitions, etc.).

TIP: Do you want to maintain really good signal quality even after bridging? Therefore, place the secondary router where at least 50% of the signal strength from the main (primary) router is maintained.

Tynker is a modern platform that teaches kids to program in a fun way. With the help of visual blocks, they can create their own games, animations or control robots. The platform supports creativity, logical thinking and allows kids to explore technology in a playful way. Find out how it works and what makes it better or worse than other platforms.

Digital blackout. ChatGPT, Sora, Instagram, and Facebook were down. Millions of users were left without access to their favorite services. The outages revealed the fragility of the online world and dependency on technology. OpenAI struggled with server issues, while Meta dealt with a global outage. What is happening behind the walls of the tech giants?

Do you want your child to learn the basics of programming in a fun and accessible way? Scratch is the ideal starting point. This visual programming language allows children to create games, animations, and stories without the need to write complex code. They will learn the basics of logical thinking and creativity, opening doors to real programming.

Wi-Fi 6, the latest wireless network standard, brings a revolution in speed, capacity, and efficiency. With new technologies like OFDMA, MU-MIMO, and BSS Coloring, it can provide up to four times the throughput and serve more devices simultaneously. Find out how Wi-Fi 6 can help you at home and in the office.

Programming is not just about writing codes, it is a path to developing logical thinking and creativity. Discover how you can introduce children to the world of programming in a fun way, from simple block languages to real coding.

Fake followers are like digital doping - a quick path to popularity with devastating consequences. Discover with us the dark side of influencer marketing, where thousands of followers can be bought for a few hundred crowns. What impact does this phenomenon have on brands, society, and especially the younger generation?